A stability question can feel straightforward on paper, then become difficult the moment an assessor changes one detail: fuel is partly used, a deck load is lifted, or a tank is slack. Vessel stability calculations are not just about remembering a formula. They show whether you can recognise how a real vessel’s loading condition affects safety before it leaves the berth.

For Coxswain and Master candidates, this is often a subject that has gone rusty during the gap between course completion and final assessment. The good news is that stability becomes far more manageable when you understand what each figure represents, work in a consistent order and explain your reasoning aloud.

Why vessel stability calculations matter at sea

A vessel that is upright at the wharf is not automatically stable at sea. Stability is the vessel’s ability to return towards upright after being heeled by wind, turning, a following sea, a shifting load or people moving to one side. It is particularly relevant to smaller commercial vessels, where fuel, water, catch, stores and passengers can make a noticeable difference to the vessel’s centre of gravity.

AMSA assessors are looking for more than a correct numerical answer. They want to hear that you understand the operational consequence. If a calculation shows reduced GM, for example, you should be able to say that the vessel has reduced initial stability and may feel tender, with a slower, deeper roll. If GM becomes negative, the vessel has lost initial stability and is unsafe in that condition.

The exact depth of calculation depends on the certificate being assessed and the vessel information provided. A Coxswain candidate may be asked to demonstrate sound practical judgement around loading and free surface effect, while a Master candidate may need to work through a fuller loading problem using hydrostatic data. In either case, the process matters.

The key terms behind vessel stability calculations

Before reaching for a calculator, be clear about the reference points. A common source of mistakes is using a formula correctly but confusing the meaning of KG, KM and GM.

G is the vessel’s centre of gravity. Its vertical position above the keel is called KG. Loading weight high on the vessel raises KG; loading weight low down reduces it.

B is the centre of buoyancy, the centre of the underwater volume of the hull. As the vessel heels, the shape of the underwater volume changes and B moves towards the low side.

M is the metacentre for small angles of heel. Its height above the keel is KM, usually obtained from the vessel’s hydrostatic information for the relevant displacement or draught.

GM is the metacentric height:

`GM = KM – KG`

A positive GM means M is above G and the vessel has positive initial stability. A larger positive GM generally gives a stiffer vessel with a quicker roll. That does not mean bigger is always better. Excessive stiffness can produce a sharp, uncomfortable roll and increase loads on gear, people and the vessel. Safe operation is about remaining within the vessel’s approved loading and stability limits, not chasing the highest possible GM.

A reliable order for working the problem

Assessment questions are easier when you use the same sequence every time. Start by identifying the vessel’s displacement, then calculate the vertical centre of gravity, obtain the relevant KM and apply any corrections before stating what the result means.

For a basic loading calculation, find the vertical moment of every item of weight:

`Vertical moment = weight × KG`

Add all weights to find total displacement. Add all vertical moments, then divide total moment by total displacement:

`KG = total vertical moments ÷ total displacement`

Keep units consistent throughout. If displacement is in tonnes and KG is in metres, moments are tonne-metres. Mixing kilograms with tonnes, or millimetres with metres, is an easy way to create an answer that looks plausible but is wildly wrong.

Once KG is known, take KM from the supplied hydrostatic table or curve at the calculated displacement. Then calculate GM. Do not use a KM value from a different draught simply because it is close. In an assessment, saying you would interpolate between the two surrounding values where required demonstrates good care.

A simple loading change example

Suppose a vessel displaces 20 tonnes with a KG of 2.0 metres. Its total vertical moment is therefore 40 tonne-metres. A 1-tonne item is loaded at a KG of 5.0 metres.

The new displacement is 21 tonnes. The new total moment is 45 tonne-metres, so the revised KG is:

`45 ÷ 21 = 2.14 metres`

The centre of gravity has risen by about 0.14 metres. If KM at the new displacement is 2.60 metres, GM is 0.46 metres before any free surface correction. The key operational answer is not merely that GM has changed. Loading the item high has reduced the vessel’s reserve of initial stability. You would consider whether the load can be stowed lower, whether the loading condition remains approved and what effect further fuel use or sea conditions may have.

Free surface effect: the trap assessors often test

A slack liquid tank is one that is neither pressed full nor empty. When the vessel heels, liquid moves across the tank towards the low side. That movement acts as though weight has been raised, reducing effective GM. Fuel, fresh water, fish holds, bilges and other liquids can all create free surface effect.

The free surface correction is often supplied in the question, or calculated from a free surface moment. The usual relationship is:

`Free surface correction = free surface moment ÷ displacement`

The correction is deducted from the uncorrected GM:

`Corrected GM = KM – KG – free surface correction`

If several slack tanks are present, their free surface moments are added before dividing by displacement. Be careful with tank data. A free surface moment may need a density correction if the information is based on fresh water and the tank contains diesel or another liquid. Use the figures and instructions supplied in the question rather than assuming every liquid behaves identically.

Operationally, the best response is usually to avoid carrying tanks slack where practicable. Press tanks full or empty, transfer liquid carefully in accordance with vessel procedures, and remember that a tank’s effect can change as fuel is consumed. A vessel may depart in a satisfactory condition and become less stable later in the trip if tanks are allowed to remain partly full.

Weight shifts and suspended loads

Not every stability problem involves adding cargo. An existing weight can be moved vertically, transversely or longitudinally. The method depends on the movement described.

For a vertical shift, calculate the rise or fall of G using:

`GG1 = weight shifted × vertical distance moved ÷ displacement`

A weight shifted upwards raises G and reduces GM by the same amount. A weight shifted downwards lowers G and increases GM. For a transverse shift, G moves towards the shifted weight and the vessel takes a list. A competent Master does not simply calculate the list and carry on. They identify the cause, consider shifting weight back, check for water ingress or a slack tank, and ensure the vessel is safe before proceeding.

Suspended loads need special attention. Once a load is lifted clear of the deck by a crane, derrick or davit, its effective point of application is at the point of suspension. This can raise the vessel’s effective centre of gravity substantially. Before lifting, consider the load weight, boom position, radius, sea state, heel, free surface in tanks and any limits in the vessel’s lifting or stability information.

How to answer stability questions in an oral assessment

A confident answer has a clear structure. State the condition you are calculating, identify the data you need, talk through the formula and then interpret the result in practical terms. Slow down enough for the assessor to follow your working. If you make an arithmetic error, recognise it, correct it and continue. That is far better than guessing.

It also helps to connect the numbers to the vessel in front of you. If asked what you would check before departure, explain that you would confirm the loading condition, stowage security, tank status, weather forecast, passenger or crew distribution, deck cargo and relevant stability documentation. If the calculation indicates an unacceptable condition, the answer is not to “take it easy”. The answer is to change the loading condition or delay departure until the vessel is safe.

Build calculation confidence before the assessment

The quickest way to improve is to work several questions by hand, not just read model answers. Practice lightship-to-loaded conditions, high deck loads, slack tanks, weight transfers and suspended-load scenarios. Say each step aloud as you work. This exposes gaps in your understanding well before an assessor asks the question.

At True North Marine Training, individual tutoring can focus directly on the calculations and oral explanations that are causing trouble, rather than making you repeat subjects you already know. Targeted revision is particularly useful when sea service has taken you away from classroom work for months or years. For more information on our one-on-one tutoring service please go to our website at https://www.truenorthmarine.com.au

Stability is ultimately a practical safety decision supported by numbers. Learn the sequence, check the units, understand the effect of every loading change and be prepared to explain what you would do next. That approach will help you in an assessment, but more importantly, it will help you make sound decisions when the vessel and the people aboard depend on them.